EDI — Elektronikas un datorzinātņu institūts
Atpakaļ uz personālu

Didzis Lapsa

Mg. sc. ing.

Pētnieks

Didzis Lapsa ir Elektronikas un datorzinātņu institūta (EDI) pētnieks, kurš savas darba gaitas institūtā uzsāka 2014. gada novembrī, iesaistoties valsts pētījumu projektā KiFiS, kur strādāja pie iegulto sistēmu un bezvadu sensoru mezglu testgultnes izstrādes. 2018. gadā ieguvis profesionālo bakalaura grādu elektrotehnikā Rīgas Tehniskajā universitātē, bet 2019. gadā – profesionālo maģistra grādu elektrotehnikas un datorzinātņu specialitātē. Kopš 2020. gada studē Latvijas Universitātē datorzinātņu doktorantūras studiju programmā.

Galvenie pētniecības virzieni aptver elektroinženieriju, iegultās sistēmas, sensoru tehnoloģijas, spiesto plašu (PCB) projektēšanu, mērījumu un instrumentācijas sistēmas, enerģijas patēriņa optimizāciju sensoru mezglos, kā arī kiberfizikālo sistēmu risinājumus un fizioloģisko signālu apstrādi. Pašreizējā zinātniskā darbība galvenokārt vērsta uz efektīvu un uzticamu sensoru sistēmu izstrādi, īpašu uzmanību vēršot uz bioimpedances mērījumiem sirdsdarbības detektēšanai, signālapstrādi un uzticamu algoritmu izstrādi fizioloģisko signālu analīzei.

Didzis piedalījies EDI WSN testgultnes (EDI TestBed) izstrādē, kas izmantota plaši pētniecībā un starptautiskās publikācijās, kā arī izstrādājis un līdzautorizējis vairākus zinātniskus darbus bioimpedances mērījumu un signālapstrādes jomā (t.sk. Sensors, Applied Sciences, IEEE konferenču publikācijas).

Ārpus akadēmiskās darbības Didzis aizraujas ar tehnoloģiju popularizēšanu, uzturot nelielu izglītojošu YouTube kanālu, nodarbojas ar elektronikas ierīču remontu un foto/video projektiem. Brīvajā laikā mācās spēlēt ģitāru un hobija līmenī nodarbojas ar ainavu fotogrāfēšanu.

Projekti

9 rezultāti

Publikācijas

  • 2024

    PPG and Bioimpedance-Based Wearable Applications in Heart Rate Monitoring—A Comprehensive Review(atveras jaunā logā)

    Didzis Lapsa, Rims Janeliukstis, Margus Metshein, Leo Selavo

    Applied Sciences, Sēj. 14 (17), lpp. 7451, MDPI

    Kopsavilkums

    The monitoring of hemodynamic parameters, such as heart rate and blood pressure, provides valuable indications of overall cardiovascular health. It is preferable that such monitoring is non-invasive and in real time via an affordable, compact and small-scale device for maximum convenience. Numerous literature sources have exploited derivations of these parameters from photoplethysmogram (PPG) and electrical bioimpedance (EBI) signal measurements through the use of calculation algorithms of varying complexity. Compared to electrocardiogram (ECG), these measurement techniques have a merit of well-established practices of designing a wearable device that could conveniently be put on a wrist. The current paper provides a comprehensive review on the use of PPG and EBI measurement techniques in the context of hemodynamic parameter monitoring using a wearable device. A special emphasis is placed on the most basic hemodynamic parameter—heart rate—describing different algorithms of heart rate detection and monitoring. The last section provides an overview of commercially available and in-home wearable device technologies based on PPG and EBI measurements, their design challenges, and future prospects.

    Indeksēts Scopus / WoS · Scopus procentile: 75

  • 2024

    Evaluation of Two-Electrode System Configurations for Forearm Arteries Bioimpedance Measurement(atveras jaunā logā)

    Margus Metshein, Ksenija Pesti, Didzis Lapsa, Paul Annus, Rims Janeliukstis, Atis Elsts, Olev Martens

    2024 IEEE International Instrumentation and Measurement Technology Conference (I2MTC), lpp. 1-6

    Kopsavilkums

    Pulse wave monitoring for hemodynamic parameter acquisition, including blood pressure, constitutes a challenge for wearable device development. Hypertension as a target for such development forms a global health issue. An important aspect is the connection to the object-electrode-skin interface-from which many problems in electrical measurements originate. Finite element model simulations and experimental measurements of forearm arteries' electrical bioimpedance have been presented in this paper to evaluate the two-electrode system compared to the four-electrode system in distal and perpendicular placement relative to the artery. The four-electrode system has been reported to provide higher pulsating blood volume proportions, reaching 0.09% from the total measured impedance in distal placement, while the two-electrode system exhibits lower values (0.05%). A strong positive correlation between the simulation and experimental results appeared in distal two-electrode placement (r=0.718), while the outcome is reversed in the perpendicular approach (r=-0.539). The experimented two-electrode system configurations are applicable in wearable device development but require further analysis for the perpendicular placement.

    Indeksēts Scopus / WoS

  • 2024

    Signal Acquisition and Algorithm Design for Bioimpedance-Based Heart Rate Estimation from the Wrist(atveras jaunā logā)

    Didzis Lapsa, Margus Metshein, Andrei Krivošei, Rims Janeliukstis, Olev Märtens, Atis Elsts

    Applied Sciences, Sēj. 14 (21), lpp. 9632, MDPI

    Kopsavilkums

    Background: Heart rate (HR) is a critical biomarker that provides insights into overall health, stress levels, and the autonomic nervous system. Pulse wave signals contain valuable information about the cardiovascular system and heart status. However, signal acquisition in wearables poses challenges, particularly when using electrical sensors, due to factors like the distance from the heart, body movement, and suboptimal electrode placement. Methods: Electrical bioimpedance (EBI) measurements using bipolar and tetrapolar electrode systems were employed for pulse wave signal acquisition from the wrist in both perpendicular and distal configurations. Signal preprocessing techniques, including baseline removal via Hankel matrix methods, normalization, cross-correlation, and peak detection, were applied to improve signal quality. This study describes the combination of sensor-level signal acquisition and processing for accurate wearable HR estimation. Results: The bipolar system was shown to produce larger Δ𝑍(𝑡)ΔZ(t), while the tetrapolar system demonstrated higher sensitivity. Distal placement of the electrodes yielded greater Δ𝑍(𝑡)ΔZ(t) (up to 0.231 ΩΩ) when targeting both wrist arteries. Bandpass filtering resulted in a better signal-to-noise ratio (SNR), achieving 3.6 dB for the best bipolar setup and 4.8 dB for the tetrapolar setup, compared to 2.6 and 3.3 dB SNR, respectively, with the Savitzky–Golay filter. The custom HR estimation algorithm presented in this paper demonstrated improved accuracy over a reference method, achieving an average error of 1.8 beats per minute for the best bipolar setup, with a mean absolute percentage error (MAPE) of 8%. Conclusions: The analysis supports the feasibility of using bipolar electrode setups on the wrist and highlights the importance of electrode positioning relative to the arteries. The proposed signal processing method, featuring a preprocessing pipeline and HR estimation algorithm, provides a proof-of-concept demonstration for HR estimation from EBI signals acquired at the wrist.

    Indeksēts Scopus / WoS · Scopus procentile: 75

  • 2023

    Wireless induction charging station for industrial application(atveras jaunā logā)

    Pēteris Aizpurietis, Didzis Lapsa, Niklāvs Barkovskis, Arnis Salmiņš, Rims Janeliukštis, Kaspars Ozols

    2023 Workshop on Microwave Theory and Technology in Wireless Communications (MTTW), lpp. 62-66, IEEE

    Kopsavilkums

    Wiring for charging LiPo batteries poses problems due to electromagnetic interference and limitations of wire length. In this work, a method for charging wireless sensor network wirelessly using NRF52840 is developed for both transmitting and receiving side of equipment. A Qi-compliant WE760308103202 wireless charging coil receiver is used and its performance evaluated to estimate optimal parameters of wireless charging, such as load and resonance frequency detuning for receiver. By tuning the frequency of operation, it is possible to utilize generic electronic components with reduced costs.

    Indeksēts Scopus / WoS

  • 2023

    Adaptive Signal-to-Noise Ratio Indicator for Wearable Bioimpedance Monitoring(atveras jaunā logā)

    D. Lapsa, R. Janeliukstis, A. Elsts

    Sensors, Sēj. 23 (20), lpp. 8532, MDPI

    Kopsavilkums

    Bioimpedance monitoring is an increasingly important non-invasive technique for assessing physiological parameters such as body composition, hydration levels, heart rate, and breathing. However, sensor signals obtained from real-world experimental conditions invariably contain noise, which can significantly degrade the reliability of the derived quantities. Therefore, it is crucial to evaluate the quality of measured signals to ensure accurate physiological parameter values. In this study, we present a novel wrist-worn wearable device for bioimpedance monitoring, and propose a method for estimating signal quality for sensor signals obtained on the device. The method is based on the continuous wavelet transform of the measured signal, identification of wavelet ridges, and assessment of their energy weighted by the ridge duration. We validate the algorithm using a small-scale experimental study with the wearable device, and explore the effects of variables such as window size and different skin/electrode coupling agents on signal quality and repeatability. In comparison with traditional wavelet-based signal denoising, the proposed method is more adaptive and achieves a comparable signal-to-noise ratio.

    Indeksēts Scopus / WoS · Scopus procentile: 87

Patenti

  • LR patents Nr. 15878 A

    IERĪCE UN METODE BIOIMPEDANCES SIGNĀLA KVALITĀTES NOVĒRTĒŠANAI

    Apraksts un saite

    LR patents Nr. 15878 A, "IERĪCE UN METODE BIOIMPEDANCES SIGNĀLA KVALITĀTES NOVĒRTĒŠANAI"

    Skatīt patentu Espacenet datubāzē(atveras jaunā logā)
  • 2018 LR patents Nr. 15308

    Mobila ierīce bezvadu sensoru tīklu un to mezglu efektīvai izstrādei mērķa vide

    Izgudrotāji:Leo SEĻĀVO, Krišjānis NESENBERGS, Jānis JUDVAITIS, Didzis LAPSA, Rihards BALAŠS, Arnis SALMIŅŠ, Modris GREITĀNS

    Apraksts un saite

    LR patents Nr. 15308 “Mobila ierīce bezvadu sensoru tīklu un to mezglu efektīvai izstrādei mērķa vide”, Izgudrotāji Leo SEĻĀVO, Krišjānis NESENBERGS, Jānis JUDVAITIS, Didzis LAPSA, Rihards BALAŠS, Arnis SALMIŅŠ, Modris GREITĀNS, publicēts 20.03.2018.

    Skatīt patentu Espacenet datubāzē(atveras jaunā logā)